Skip to article

Why did contacts stop partway?

Short answer

Usually a Send email step couldn’t send its email, so Jounce stopped those people there rather than send something broken. Fix the email, then resume them.

Most often, Jounce reached a Send email step for those people and couldn’t send the email, so it stopped them there. Nobody got a broken email, and nobody else in the automation was affected. The yellow strip under the top bar counts them. The automation’s results page says the same.

The yellow strip on a live automation, reading 3 contacts stopped partway, with the Resume contacts button ringed at its right.

What stops a step

The strip points at the fix. Fix the listed step and Fix the listed email mean the list at the bottom of the settings panel names the step. It’s titled Needs fixing on a live automation, and Before you go live on a paused one.

With no step open, select the Settings edge to show the list, then select the line. The step’s settings open, and a problem inside the email shows there in red, beside Edit the email.

Check the email steps means the list names nothing to fix. Either someone has fixed the cause since, or it’s one of the last three below, which the list never names. These are the reasons a step stops:

  • The email is gone. The list reads One step’s email can’t be found, and the step’s card on the board reads Choose another email. Jounce never sends a deleted email, so these people have stopped for good. Select the line, then Choose another email so new contacts get one. See The Send email step.
  • A block’s design is missing. The step’s panel says Your email has a block with a missing design. Open the email and delete the block that reads This block can’t be shown. See Why does a block say it can’t be shown?
  • A button or link has no real web address. The step’s panel says Your button points somewhere that isn’t a real web address. Open the email and add a real web address to each one.
  • The email has no content, or almost no live text. The step’s panel says Your email still needs some text. Live text is words a mail app shows as text, not as part of a picture. Add a text block.
  • Its only words are inside pictures. A design that goes out as a picture is sent as an image, the same for everyone. Its words don’t count as live text, so the panel says Your email still needs words outside its pictures.
  • A personalization tag or a link sits inside a picture. The panel says so, such as Your email has a link inside a picture. Neither works in a design that goes out as a picture. Move the tag into text outside the picture, and put the link on the design’s button.
  • The email has too many designs that go out as pictures. Each video on its own is one. The step’s panel says Your email has too many designs that go out as pictures. Open the email, where the line under Before you send says how many to delete.
  • The email still has something Jounce left open. This can happen in any email made in the current editor. The leftover is sample text, or a testimonial with sample or made-up words. Or it’s a missing number, an empty picture, or a countdown with no end time. The placeholder words in an item you add to a list count as sample text. The step’s panel names it. See What an AI draft leaves to you.
  • Jounce needs your saved brand kit to make this email. Open your brand kit and save it.
  • A picture inside a design that goes out as a picture didn’t load from its web address. A test send tells you. Open the email and select Send test. The test doesn’t go out, and the message names the design and counts the pictures. Replace them in the editor. See Why won’t my test email send?
  • Jounce couldn’t put the email together. This one is on Jounce. It’s usually over by the time you look, and there’s nothing for you to change.

These are the same reasons a one-off send fails, in the same words. See Why did my send fail?

Then resume them

Once you fix the email, select Resume contacts. The people carry on from the step they stopped at. Nobody gets a step’s email twice. See Resume stopped contacts

While the list still names a problem inside an email, the strip has no Resume contacts. It ends Fix the listed email, then you can resume them. Fix the email, and the button comes back.

When the strip says stopped for good

The strip can read 3 contacts stopped for good. Jounce can’t restart them, so the strip has no Resume contacts button. The rest of the line says whether there is anything to change.

  • Nothing to fix — new contacts run your current steps. Usually the step they stopped at is gone or can’t be read, or it’s a step you’ve since fixed. Some went round the same steps too many times, or were resumed as often as Jounce will try.
  • Fix the listed step so new contacts don’t stop there too. The list in the settings panel names the step. If a Condition’s filters check a deleted segment, its line reads One condition checks a deleted segment. If a Send email step’s email is gone, it reads One step’s email can’t be found. Jounce stops everyone who reaches that step. See The Condition step.

Replacing the segment, or choosing another email, fixes the step for everyone who enters after the change. People already inside finish the path they started on, so those still on their way to that step stop there too. See Editing a live automation.

Also answered here

  • what does stopped for good mean
  • why did my automation stop for some people
  • check the email steps so it doesn't happen again

Updated

New to Jounce? See what Jounce does