# Why did contacts stop partway?

> **Short answer:** Usually a Send email step couldn’t send its email, so Jounce stopped those people there rather than send something broken. Fix the email, then resume them.

Most often, Jounce reached a Send email step for those people and couldn't
send the email, so it stopped them there. Nobody got a broken email, and nobody else in the automation was affected. The yellow strip under the top bar
counts them. The automation's results page says the same.

![The yellow strip on a live automation, reading 3 contacts stopped partway, with the Resume contacts button ringed at its right.](https://help.jounce.com/kb/shots/automations-design--stopped-strip--desktop--light.webp)

## What stops a step

The strip points at the fix. _Fix the listed step_ and _Fix the listed email_ mean the list at the bottom of the settings panel names the
step. It's titled **Needs fixing** on a live automation, and **Before you
go live** on a paused one.

With no step open, select the **Settings** edge to show the list, then
select the line. The step's settings open, and a problem inside the email
shows there in red, beside **Edit the email**.

_Check the email steps_ means the list names nothing to fix. Either someone
has fixed the cause since, or it's one of the last three below, which the list
never names. These are the reasons a step
stops:

- **The email is gone.** The list reads _One step’s email can’t be found_,
  and the step's card on the board reads _Choose another email_. Jounce never
  sends a deleted email, so these people have stopped for good. Select the
  line, then **Choose another email** so new contacts get one. See
  [The Send email step](https://help.jounce.com/automations/the-trigger-and-steps/the-send-email-step).
- **A block's design is missing.** The step's panel says _Your email has a
  block with a missing design_. Open the email and delete the block that
  reads _This block can't be shown_. See
  [Why does a block say it can't be shown?](https://help.jounce.com/emails/the-editor/why-does-a-block-say-it-cant-be-shown)
- **A button or link has no real web address.** The step's panel says
  _Your button points somewhere that isn't a real web address_. Open the
  email and add a real web address to each one.
- **The email has no content, or almost no live text.** The step's panel
  says _Your email still needs some text_. Live text is words a mail app
  shows as text, not as part of a picture. Add a text block.
- **Its only words are inside pictures.** A design that goes out as a
  picture is sent as an image, the same for everyone. Its words don't count
  as live text, so the panel says _Your email still needs words outside its
  pictures_.
- **A personalization tag or a link sits inside a picture.** The panel says
  so, such as _Your email has a link inside a picture_. Neither works in a
  design that goes out as a picture. Move the tag into text outside the
  picture, and put the link on the design's button.
- **The email has too many designs that go out as pictures.** Each video on
  its own is one. The step's panel says _Your email has too many designs
  that go out as pictures_. Open the email, where the line under **Before
  you send** says how many to delete.
- **The email still has something Jounce left open.** This can happen in
  any email made in the current editor. The leftover is sample text, or a
  testimonial with sample or made-up words. Or it's a missing number, an
  empty picture, or a countdown with no end time. The placeholder words in
  an item you add to a list count as sample text. The step's panel names
  it. See
  [What an AI draft leaves to you](https://help.jounce.com/emails/create-an-email/what-an-ai-draft-leaves-to-you).
- **Jounce needs your saved brand kit to make this email.** Open your brand
  kit and save it.
- **A picture inside a design that goes out as a picture didn't load from
  its web address.** A test send tells you. Open the email and select
  **Send test**. The test doesn't go out, and the message names the design
  and counts the pictures. Replace them in the editor. See
  [Why won't my test email send?](https://help.jounce.com/emails/the-editor/why-wont-my-test-email-send)
- **Jounce couldn't put the email together.** This one is on Jounce. It's usually over by the time you look,
  and there's nothing for you to change.

These are the same reasons a one-off send fails, in the same words. See
[Why did my send fail?](https://help.jounce.com/emails/after-sending/why-did-my-send-fail)

## Then resume them

Once you fix the email, select **Resume contacts**. The people carry on
from the step they stopped at. Nobody gets a step's email twice. See
[Resume stopped contacts](https://help.jounce.com/automations/launch-and-running/resume-stopped-contacts)

While the list still names a problem inside an email, the strip has no
**Resume contacts**. It ends _Fix the listed email, then you can
resume them_. Fix the email, and the button comes back.

## When the strip says stopped for good

The strip can read _3 contacts stopped for good_. Jounce can't restart them, so the strip has no **Resume contacts**
button. The rest of the line says
whether there is anything to change.

- _Nothing to fix — new contacts run your current steps_. Usually the step
  they stopped at is gone or can't be read, or it's a step you've since fixed.
  Some went round the same steps too many times, or were resumed as often as
  Jounce will try.
- _Fix the listed step so new contacts don’t stop there too_. The
  list in the settings panel names the step. If a Condition's filters check a deleted
  segment, its line reads _One condition checks a deleted segment_. If a
  Send email step's email is gone, it reads _One step’s email can’t be
  found_. Jounce stops everyone who reaches that step. See
  [The Condition step](https://help.jounce.com/automations/the-trigger-and-steps/the-condition-step).

Replacing the segment, or choosing another email, fixes the step for everyone
who enters after the change. People already inside finish the path they started on, so those still on their way to that step stop there too. See
[Editing a live automation](https://help.jounce.com/automations/the-builder/editing-a-live-automation).

## Also answered here

- “what does stopped for good mean”
- “why did my automation stop for some people”
- “check the email steps so it doesn't happen again”

---

Updated 2026-11-12 · https://help.jounce.com/automations/launch-and-running/why-did-contacts-stop-partway
