# How contacts move through an automation

> **Short answer:** Someone enters the moment the trigger happens, walks the steps one by one on their own clock, and leaves at the end. The number on a card counts the people at that step right now.

An automation is a path, and each contact walks it alone. Two people
who entered a day apart are a day apart at every step. Some tools call an
automation a workflow or a sequence.

## Entering

Someone enters the moment the trigger happens for them. Each person enters
an automation only once. Only people with the **Subscribed** status enter.
See [The trigger](https://help.jounce.com/automations/the-trigger-and-steps/the-trigger).

Each automation is its own path. A person can be inside several at the same
time, and each one counts them on its own.

## Moving

Jounce takes each person down the canvas one card at a time. A Send email
step sends and moves them on. A Time delay holds them until the wait ends.

A Condition checks them, or waits for the open or click, and sends them down
**Yes** or **No**. A Percentage split sorts them into a branch. An Action adds
them to a segment or removes them from one, then moves them on. See
[How steps connect](https://help.jounce.com/automations/the-trigger-and-steps/how-steps-connect).

## The numbers you see

While the automation is live, a card shows a small number at its right
edge. It counts the people standing at that step at this moment. Most of them are
waiting at a Time delay or a Condition. A card with nobody at it shows no
number.

![A Time delay card reading Wait 3 days, with the number 23 at its right edge for the people waiting there.](https://help.jounce.com/kb/shots/automations-design--step-count--desktop--light.webp)

The Automations page adds them up. The card's _in it now_ line and the
list's **In it now** column count everyone inside, at any step. See
[The Automations page](https://help.jounce.com/automations/your-automations/the-automations-page).

These are counts. Jounce doesn't list who is inside. A contact's page doesn't say which
automations they're in either.

## Before each email

Jounce looks at the person again before every Send email step. If someone
unsubscribed, bounced, complained, or was removed since they entered, they
don't get that email. The same goes for an address on your suppression list
or on Jounce's list of addresses it can't send to, someone not yet
confirmed, or an address whose domain can't receive mail.

Jounce skips the email and moves them on to the next step. Skipping an email doesn't stop them or take them out of the automation. If an
email you expected hasn't gone out, see
[Why hasn't the next email gone out?](https://help.jounce.com/automations/launch-and-running/why-hasnt-the-next-email-gone-out)

### A new contact's email can wait

When someone joins as **Subscribed** straight away, Jounce checks that the
domain in their address can receive mail. An email that comes due before the
check is done waits at its Send email step. They're inside the automation the
whole time, and that card's number counts them.

- If Jounce already knows the domain receives mail, as with Gmail or
  Outlook, the email doesn't wait.
- Otherwise the check usually takes about two minutes.
- If the domain looks like it can't receive mail, Jounce takes up to about
  two hours to be sure. If it really can't, Jounce skips the email.
- If the check can't finish, the email goes out about three hours after they
  joined.

After you import a long list, people can enter a little later. If Jounce
couldn't check every address during the import, it gives itself time to check
the rest first. That's a few minutes, or up to about an hour for a very large
list. No card counts them until they enter.

Someone who confirms through your confirmation email isn't checked this way.
Once a person's check is done, their emails don't wait for it again.

## Leaving

A person finishes when they pass the last card on their path. If the path
ends in an **Exit automation** step, they leave there instead. They have
left, so the results page doesn't count them under **Finished**.

Finished or left, a person no longer counts as in the automation. The same
automation never takes them in again. See
[Automation statuses](https://help.jounce.com/automations/your-automations/automation-statuses).

## While people are inside

You can change the steps while people are inside. The people already in it
finish the path they started on. But a changed email reaches everyone the
step hasn't sent to yet. See
[Editing a live automation](https://help.jounce.com/automations/the-builder/editing-a-live-automation).

## Also answered here

- “what does the number on a step card mean”
- “does a new contact's first email go out right away”
- “can one person be in two automations at the same time”

---

Updated 2026-10-29 · https://help.jounce.com/automations/launch-and-running/how-contacts-move-through-an-automation
